Louisiana OMV CDL General Knowledge Practice Test 6

  • Questions50
  • Correct to pass40
  • Passing score80%
  • Minimum age18 years

Minimum age: 18 years for intrastate operation, 21 years for interstate operation

50 questions. Pick an answer to see if it is right and why; you need 40 correct answers to pass.

  1. 1. What can repeated violations of the federal phone and texting rules cost a commercial driver?

    Show answer

    Answer D: Disqualification of the commercial driver license

    Multiple convictions for using a hand-held phone or texting while driving a commercial vehicle lead to disqualification, on top of fines for driver and carrier.

  2. 2. How does overloading affect the way a vehicle drives?

    Show answer

    Answer C: It slows the vehicle on upgrades, makes stopping take longer and can overheat the brakes on downgrades

    Extra weight demands more from the engine and the brakes, so the vehicle climbs slowly and needs much more distance to stop.

  3. 3. An angry driver has cut in front of you and is now braking hard to provoke you. What is the safest response?

    Show answer

    Answer D: Drop back, avoid eye contact and let the driver go

    Giving an aggressive driver space and no response removes the conflict, while any answering gesture invites escalation you cannot control in a heavy vehicle.

  4. 4. Federal rules forbid operating a commercial vehicle in which condition?

    Show answer

    Answer C: In a condition likely to cause a crash or a breakdown

    A defect that makes a crash or a breakdown likely has to be corrected before the vehicle is driven, not reported at the end of the trip.

  5. 5. Why should a retarder be switched off when the road is wet, icy or snowy?

    Show answer

    Answer C: It can make the drive wheels skid when traction is poor

    A retarder slows the drive wheels only, and on a slippery surface that braking force can break their traction and start a skid.

  6. 6. You press on a drive belt and it deflects far more than the others. What does that suggest?

    Show answer

    Answer C: The belt is too loose and the part it drives may not work properly

    A belt with excessive play slips on its pulleys, so the accessory it drives turns too slowly or not at all under load.

  7. 7. What is the danger of letting engine speed climb past the top of the rated rpm range before you shift?

    Show answer

    Answer B: You can damage the engine, so the shift should be made before that point

    Every engine has a rated operating range; running above it can cause serious engine damage, so the upshift belongs at the top of that range, not beyond it.

  8. 8. The shipper hands you the placards for a load that needs them. Who puts them on the vehicle?

    Show answer

    Answer C: The driver, who must also make sure they are the correct ones and are readable

    The shipper supplies the placards, but it is the driver who must place them on the vehicle and confirm that they match the load and can be read.

  9. 9. What tells you that an air suspension bag has a problem?

    Show answer

    Answer B: The bag is leaking or damaged, or the vehicle sits unevenly on that side

    An air bag that leaks or is cut lets that corner of the vehicle settle, which throws the load onto the other suspension parts and changes the ride height.

  10. 10. What happens to braking distance when speed is doubled?

    Show answer

    Answer C: It becomes about four times longer

    Braking distance grows with the square of speed, so doubling the speed multiplies both the braking distance and the force of an impact by about four.

  11. 11. Federal rules keep recapped and retreaded tires off the front wheels of which vehicle?

    Show answer

    Answer B: Any bus carrying passengers

    The federal rule names buses: a bus may not run with regrooved, recapped or retreaded tires on its front wheels, because a steer tire failure with passengers aboard takes away steering control.

  12. 12. When should mirror adjustment be checked, and what should each mirror show?

    Show answer

    Answer B: Before every trip, with each mirror adjusted to show some part of the vehicle

    Checking the mirrors before each trip and keeping a small part of the vehicle in view gives a reference point for judging distance behind and beside you.

  13. 13. Below 40 mph, what following distance does the standard commercial rule of thumb call for?

    Show answer

    Answer C: One second for every 10 feet of vehicle length

    The base rule allows one second of space for each 10 feet of vehicle length while speed stays under 40 mph.

  14. 14. You are told a posted bridge ahead has a weight limit lower than your gross weight. What must you do?

    Show answer

    Answer C: Take a route that avoids it, because a posted limit is a legal limit

    A posted structure limit must be obeyed exactly as any other weight limit, so a heavier vehicle has to be routed around it.

  15. 15. What should you do before backing into a space you have not used before?

    Show answer

    Answer A: Get out and walk around to check the path, the clearance and any obstacles

    Walking the area first reveals low obstructions, soft ground and objects that never appear in the mirrors.

  16. 16. A straight truck has a long body behind the rear axle. What happens to that overhang in a sharp left turn?

    Show answer

    Answer D: It swings out to the right and can strike a vehicle or an object on that side

    Body that hangs behind the rear axle swings the opposite way to the turn, so the tail of the truck sweeps out into the next lane or over the curb.

  17. 17. Taking your eyes off the road for about five seconds at highway speed means traveling roughly how far unseen?

    Show answer

    Answer A: About the length of a football field

    At highway speed a five second glance away covers roughly 100 yards, which is far more road than any driver can afford to travel blind.

  18. 18. Why should the mirrors be checked repeatedly while you make a tight turn?

    Show answer

    Answer C: To watch the rear of the vehicle clear other vehicles and objects

    In a long vehicle the rear wheels cut inside the path of the front wheels, so only the mirrors show whether the rear is clearing curbs, poles and other vehicles.

  19. 19. You find a defect during the pre-trip inspection. What must happen before the vehicle is driven?

    Show answer

    Answer C: It must be repaired, or the vehicle must not be driven

    Writing a defect down does not make the vehicle safe; a defect that affects safe operation has to be corrected before the trip starts.

  20. 20. An unblocked article is 15 feet long. What is the minimum number of tiedowns?

    Show answer

    Answer B: Three

    Two tiedowns cover the first 10 feet and one more is added for each further 10 feet or any part of it, so 15 feet needs three.

  21. 21. What must be checked on a sliding fifth wheel during the inspection?

    Show answer

    Answer B: That it is locked in position and not so far forward that the trailer can hit the cab

    A slider that is unlocked can move under braking, and one set too far forward lets the trailer strike the cab when the tractor turns sharply.

  22. 22. When speed doubles, what happens to braking distance?

    Show answer

    Answer D: It becomes roughly four times as long

    Braking distance rises with the square of speed, so twice the speed needs about four times the distance to stop.

  23. 23. The scale shows that your combination is over the legal gross weight. Why will sliding the tandems not fix it?

    Show answer

    Answer B: Because sliding the axles changes where the weight sits, not how much there is

    Repositioning axles redistributes weight between axle groups; when the total is too high, freight has to come off the vehicle.

  24. 24. Why does a load need to be balanced from side to side?

    Show answer

    Answer B: Because a heavy side raises the rollover risk and can overload the tires and springs on that side

    An uneven load tips the balance of the vehicle in curves and pushes the tires and suspension on the loaded side past their rating.

  25. 25. You must leave the vehicle parked on a slight grade. What adds security beyond setting the parking brake?

    Show answer

    Answer D: Chocking the wheels so the vehicle cannot roll if the brake bleeds off

    Chocks hold the vehicle mechanically and are the standard backup whenever a parked vehicle could roll.

  26. 26. A doctor prescribes you a medicine that can cause drowsiness. What should you do?

    Show answer

    Answer A: Tell the doctor what you drive and not drive while affected

    Both prescription and over the counter medicines can make a driver unsafe, so the medical professional must know the job and the driver must stay out of the seat while affected.

  27. 27. In Louisiana, who may hold the H hazardous materials endorsement?

    Show answer

    Answer B: Only persons 21 years of age or above

    Louisiana issues the H endorsement only to applicants who are at least 21 years old.

  28. 28. What does a front-end header board on a van or flatbed protect against?

    Show answer

    Answer A: Cargo moving forward toward the cab in a crash or hard stop

    The header board, often called a headache rack, blocks forward movement of the load toward the driver.

  29. 29. When must a post-trip inspection be made?

    Show answer

    Answer D: At the end of each day the driver operates the vehicle

    The post-trip inspection closes out each driving day so that anything found is recorded before the vehicle is handed to the next driver.

  30. 30. A hazard suddenly appears ahead and you must act. Which is usually the faster way to avoid it in a heavy vehicle?

    Show answer

    Answer B: Steering around it, because you can usually turn faster than you can stop

    Stopping distance at speed is very long, so a quick turn out of the way, when there is room, avoids the crash sooner than braking.

  31. 31. Which document does Louisiana require when a driver first applies for a commercial driver's license?

    Show answer

    Answer A: A current DOT physical examination certificate

    Initial CDL issuance in Louisiana requires a current DOT physical examination form along with proof of residency, proof of Social Security number and liability insurance on personally owned vehicles.

  32. 32. What tells a driver when to shift up in a vehicle with a manual transmission?

    Show answer

    Answer C: Engine speed in rpm together with road speed

    Shift points are judged from engine rpm and road speed, using the operating range the manufacturer specifies for that engine.

  33. 33. Which set of maneuvers makes up the basic control skills part of the commercial driving test?

    Show answer

    Answer D: Straight line backing, offset backing, parallel parking and alley docking

    The basic control skills test is carried out off the road and consists of low speed exercises such as straight line backing, offset backing, parallel parking and the alley dock.

  34. 34. A driver hauling a sealed trailer that cannot be opened is still responsible for what?

    Show answer

    Answer D: Making sure the rig is not over the gross or axle weight limits

    A seal prevents inspecting the contents, but the driver must still confirm the vehicle is not overloaded.

  35. 35. How are the headlights, marker lights and turn signals checked during the seven-step inspection?

    Show answer

    Answer A: The engine is shut off, the parking brake is set, the lights are switched on and then checked from outside the vehicle

    The lights are switched on with the vehicle secured, then the driver walks around and confirms each lamp actually works and is clean.

  36. 36. Why does a cracked frame rail or cross member make a vehicle unsafe?

    Show answer

    Answer B: The frame carries the whole load, and a crack can spread until the structure fails

    The frame is the backbone that supports the body, the load and the running gear, so a crack in it is a structural failure that grows with every mile.

  37. 37. On a set of dual tires, which condition must be reported as a defect?

    Show answer

    Answer D: The two tires are touching each other or rubbing on part of the vehicle

    Duals that touch each other or the vehicle overheat and wear quickly, so they must be separated by proper spacing and inflation before driving.

  38. 38. A commercial vehicle stops on the shoulder of an undivided two-lane road that carries traffic in both directions. Where do the warning devices go?

    Show answer

    Answer B: Within 10 feet of the vehicle, plus 100 feet to the front and 100 feet to the rear

    On a two-way road the devices must mark the vehicle itself and warn traffic approaching from each direction, and they must be in place within ten minutes.

  39. 39. Which shock absorber condition is a defect?

    Show answer

    Answer C: A shock that is leaking, broken or disconnected at either mounting

    A shock that has lost its fluid or its mounting no longer damps the suspension, so the wheel bounces and loses contact with the road.

  40. 40. Regular mirror checks during a long trip can reveal which developing problem?

    Show answer

    Answer D: Smoke coming from a tire or from a wheel

    Overheating tires, wheel bearings and brakes usually show as smoke long before anything appears on the dash, and mirrors are where a driver sees it.

  41. 41. A driver behind you wants to pass and you can see that the road ahead is clear. What should you do?

    Show answer

    Answer B: Do not signal the other driver to pass; let that driver decide when it is safe

    Directing other drivers can cause a crash if you misjudge the gap, so leave the decision to the driver who is passing.

  42. 42. During the vehicle overview, what should the driver look for on the ground under the vehicle?

    Show answer

    Answer B: Fresh puddles of oil, coolant, grease or fuel

    New stains on the ground are the earliest sign of a leak, so the overview includes a look underneath before anything is opened or started.

  43. 43. What does the driver check in the final step of the seven-step inspection?

    Show answer

    Answer A: Hydraulic brake leaks where those brakes are fitted, then the parking brake and the service brakes

    The last step is done with the engine started: test for hydraulic leaks on vehicles with hydraulic brakes, then prove that the parking brake holds and that the service brakes stop the vehicle.

  44. 44. What is the purpose of the torque rods or radius rods you check on the suspension?

    Show answer

    Answer A: They hold the axle in alignment with the frame under braking and acceleration

    Torque rods resist the twisting and fore and aft forces on the axle, so a cracked or missing rod lets the axle move out of alignment.

  45. 45. A dock crew loads all of the freight at the very back of a 48 foot van trailer. What are the two consequences?

    Show answer

    Answer A: The steering axle is relieved of weight and steering becomes light, and the trailer axles may go over the limit

    Weight placed far to the rear lifts weight off the front of the combination, so the steering goes light while the trailer axles take too much of the load.

  46. 46. Which vehicle is most likely to be pushed around by a strong crosswind?

    Show answer

    Answer B: An empty van trailer

    A large flat side with very little weight behind it gives the wind the most surface and the least resistance, which is the empty van trailer.

  47. 47. Why should you avoid using your lights to tell a following driver that it is safe to pass you?

    Show answer

    Answer B: You may misjudge the gap and the driver will act on your signal

    The manual warns against signaling others to pass, because the responsibility for a head-on crash then rests on a judgment you could easily get wrong.

  48. 48. Why must you never coast down a hill in neutral or with the clutch pushed in?

    Show answer

    Answer C: You lose the braking effect of the engine and your brakes may overheat and fail

    Engine braking is what keeps a heavy vehicle in check on a grade; coasting throws it away and leaves the service brakes to do all the work until they overheat.

  49. 49. What does gross vehicle weight mean, as opposed to gross vehicle weight rating?

    Show answer

    Answer B: The actual weight of the single vehicle plus everything it is carrying

    Gross vehicle weight is what the vehicle actually weighs at that moment; the rating is the maximum the manufacturer allows it to weigh.

  50. 50. What is normally required in order to move an over-width or over-length load?

    Show answer

    Answer B: A special permit along with warning devices such as flags and signs

    Oversize movements need a permit plus marking devices, and travel is often limited to certain hours or routes.